Omnitron miConverter S-Series Manuel d'instructions télécharger pdf

miConverter S-Series User Manual

S/GXT and S/FXT

Product Overview

The miConverter S/GXT Gigabit ber to 10/100/1000BASE-T

and the S/FXT Fast Ethernet ber to 10/100/1000BASE-T

media converters are ideal for mobile applications where

light weight, compact size and low power are critical

requirements.

The miConverter S-Series delivers plug-and-play set up with an RJ-45 port that auto-

negotiates the speed, duplex mode and cross-over functions for laptops with 10BASE-T,

100BASE-TX or 1000BASE-T Ethernet.

Installation Procedure

1) Connect Cables

a. The miConverter S/GXT and S/FXT can be wall mounted using the optional wall

mount bracket (1691-0) or placed on a at level surface.

To power the module using the USB cable, connect the USB Standard Type A

connector to a USB port on the computer. Then connect the USB Micro-B connector

at the other end of the cable to the connector on the back of the miConverter. Conrm

that the module has powered up properly by checking the power status LED located

on the top of the module.

To power the module using the AC/DC adapter, connect the USB Standard Type A

connector to the AC/DC adapter and connect the AC/DC adapter to the AC outlet.

Then connect the USB Micro-B connector at the end of the cable to the connector

on the back of the miConverter. Conrm that the module has powered up properly

by checking the power status LED located on the top of the module.

b. Connect the UTP port via a Category 5 or better cable to a 10BASE-T, 100BASE-TX

or 1000BASE-T Ethernet device.

c. When using xed ber port models, connect the appropriate multimode or single-

mode ber cable to the ber port of the installed module. It is important to ensure

that the transmit (Tx) is attached to the receive side of the device at the other end and

the receive (Rx) is attached to the transmit side. Single-ber (SF) media converter

models operate in pairs. The Tx wavelength must match the Rx wavelength at

the other end and the Rx wavelength must match the Tx wavelength at the other

end.

When using an SFP model, insert the SFP Fiber transceiver into the Port 1 SFP

receptacle on the module.

NOTE: The release latch of the SFP Fiber transceiver must be in the closed (up)

position before insertion.

2) Verify Operation

Once the module has been installed, verify the module is operational by viewing the

LED indicators.

Warning

The operating description in this Instruction Manual is for use by qualied personnel

only. To avoid electrical shock, do not perform any servicing of this unit other than that

contained in the operating instructions, unless you are qualied and certied to do so

by Omnitron Systems Technology, Inc.

Warranty

This product is warranted to the original purchaser against defects in material and

workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME

warranty may be obtained by the original purchaser by REGISTERING this product

with Omnitron within 90 days from the date of shipment. TO REGISTER, COMPLETE

AND MAIL OR FAX THE ENCLOSED REGISTRATION FORM TO THE INDICATED

ADDRESS. Or you may register your product on the Internet at http://www.omnitron-

systems.com. During the warranty period, Omnitron will, at its option, repair or replace

a product which is proven to be defective.

For warranty service, the product must be sent to an Omnitron designated facility, at

Buyer’s expense. Omnitron will pay the shipping charge to return the product to Buyer’s

designated US address using Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate

use and/or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-

supplied interfacing, unauthorized modications or tampering with equipment (including

removal of equipment cover by personnel not specically authorized and certied by

Omnitron), or misuse, or operating outside the environmental specication of the product

(including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.),

or improper site preparation or maintenance.

No other warranty is expressed or implied. Omnitron specically disclaims the implied

warranties of merchantability and tness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron

shall not be liable for any direct, indirect, special, incidental, or consequential damages,

whether based on contract, tort, or any legal theory.

040-01600-001B 1/12

Page 1

Omnitron Systems Technology * 140 Technology Dr., * Irvine, CA 92618

949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com

1 2

Résumé du contenu

Page 1 - S/GXT and S/FXT

miConverter S-Series User ManualS/GXT and S/FXTProduct OverviewThe miConverter S/GXT Gigabit ber to 10/100/1000BASE-T and the S/FXT Fast Ethernet be

Page 2 - Ordering Information

LED Function“Legend”Color OFF State ON/Blinking StatePower “PWR”Green No power ON: Module has powerFiber Link Activity “F/O”Green No ber linkON: Fi

Commentaires sur ces manuels

Pas de commentaire

Omnitron miConverter S-Series Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Convertisseurs de médias en réseau Omnitron miConverter S-Series. Omnitron miConverter S-Series Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Convertisseurs de médias en réseau Omnitron miConverter S-Series